MBtekUNI 60 Docs
1 · Get started

UNI 60 specifications

Full published specifications for the MBtek UNI 60 wood boiler — 85–205 KBTU output, 40 gal water volume, 58 gal firebox, 2 in connections, 8 in flue and 1,224 lb weight.

Updated

The UNI 60 delivers 85–205 KBTU into a hydronic system, heats up to 5,000 ft², holds 40 gallons of water and weighs 1,224 lb. Every figure below comes from the current MBtek specification sheet, which supersedes the older factory manual where the two differ.

Model
UNI 60
Capacity
85–205 KBTU
Heat area
5,000 ft²
Water volume
40 gal
Firebox size
58 gal
Log length
26 in
Connection
2 in
Chimney
8 in
Width
30 in
Depth
36 in
Height
65 in
Weight
1,224 lb

Performance and construction

PropertyValue
Heat output85–205 KBTU (25–60 kW)
Nominal heated areaUp to 5,000 ft²
Minimum efficiency82 % (factory technical data)
Published efficiency86 %+ guaranteed (MBtek, UNI series)
Burn timeUp to 24 hours on a full load
Fuel typesWood, coal, woodchips, peat, mulch
CombustionForced draft, fan-controlled, three flue passes
ControllerTIS Tronic 260U
Power supply230 V / 50 Hz AC
Maximum operating pressure15 psi
Maximum test pressure50 psi
Maximum flow temperature185 °F / 85 °C
OriginMade in Europe

±5 % tolerance

The factory states that weight and dimensions may vary by ±5 %. Allow for that when planning doorways, floor loading and lifting equipment.

The full UNI range

Use this table to sanity-check the model against the load — the UNI 60 sits in the middle of the range.

MBtek UNI wood boiler unit
UNI series boiler.
BoilerUnitPRO 11PRO 30UNI 15UNI 40UNI 60UNI 95UNI 150UNI 300UNI 500UNI 1000
CapacityKBTU20–5532–10527–6851–13785–205154–338185–512320–1000545–17001000–3400
Heat areaft²15003000250040005000800012000220004000078000
Water volumegal121221304048112315515772
Connectionin222334
Chimneyin4668888121216
Firebox sizegal92825445881159278382573
Log lengthin111720242630486688132
Widthin15182428303030393958
Depthin2228253436446381105158
Heightin455555556566678484126
Weightlb400590716992122414903200505068008800

Controller specification

The TIS Tronic 260U is rated for 1 A per output and draws 4.5 W on its own.

PropertyValue
Power230 V / 50 Hz AC
Relative humidity30–75 %
Ambient temperature5–40 °C / 41–104 °F
Fan output (Q1)1 A
Central heating pump output (Q3)1 A
Hot water pump output (Q4)1 A
Power consumption, no external devices4.5 W
Fuse250 V, 3.15 A, 5 × 20 mm
Conformity2014/35/EU LVD, 2014/30/EU EMC, CE 05/2020

Full parameter ranges and defaults are in the parameter reference.

Sensors

SensorTerminalWire lengthType
Boiler (CH) temperatureT10.8 mKTY-81-210
Domestic hot water (HUW)T23 mKTY-81-210
Exhaust gasT3PT1000
Safety thermostat (STB)I11 mBimetal

The exhaust sensor is sold separately

The PT1000 exhaust gas sensor is not included in the standard controller kit. Without it the boiler cannot run in Brager Expert exhaust gases mode — which is the mode MBtek recommends for the UNI 60.

NextWhat's in the box

The packing list, and what to check before you sign for the delivery.

Frequently asked questions

On this page